Setting an anchor means dropping it, laying out enough line and then backing down gently until it digs in and holds. The three things that matter are the right anchor for the bottom, enough scope (line out compared with water depth) and a check that you are not moving. Here is the order.
What you need
- An anchor suited to the bottom. A fluke or Danforth style anchor suits sand and mud. A plow or claw style anchor suits mixed bottoms. Ask the maker for the size that fits your boat, because boats and conditions differ.
- A length of chain between anchor and line (the rode) if your boat uses one. Chain keeps the pull low and helps the anchor dig in.
- Rode long enough for the depths where you anchor, with a secure bitter end tied to the boat.
- A bow cleat or anchor roller. Arizona's handbook says to secure the anchor line to the bow, never the stern, to reduce the risk of capsizing or swamping (Arizona Game and Fish boater handbook).
Setting the anchor, step by step
- Choose the spot. Look at depth, bottom, other boats and where you will swing if wind or current shifts. Stay clear of channels and launch areas.
- Check the depth with your depth finder and add the height of your bow above the water.
- Approach slowly into the wind or current, whichever is stronger, so the boat stops over your spot.
- Stop the boat, then lower the anchor by hand until it reaches the bottom. Do not throw it, and do not stand in a loop of line.
- Back away slowly, paying out the rode as the boat moves. A common rule of thumb is a scope of five to seven times the depth for a normal anchoring and more in wind. Follow your anchor maker's guidance.
- Make the line fast at the bow cleat.
- Set the anchor. Put the engine in reverse at low power and let the line come tight. The boat should stop and the line should rise and hold taut.
- Check you are holding. Line up two landmarks on shore and watch them for a while. If they move, you are dragging.
Weighing anchor
- Start the engine and motor slowly toward the anchor while someone takes in the line.
- When the line is vertical, cleat it and let the boat's forward motion help break the anchor loose. If it will not come free, motor gently around the anchor to change the direction of the pull.
- Bring it up, clean off mud and weeds, and stow it so it cannot swing or damage the deck.
Common mistakes
- Too little scope. This is the biggest cause of dragging. Add line, then add more when wind builds.
- Dropping the anchor while the boat is moving. It piles in one heap and does not dig in.
- Tying to the stern. The stern is lower and wave action can swamp the boat.
- Not tying off the other end. An anchor that is lost with the whole line is expensive.
- Anchoring and leaving. Anchor with someone aboard who can watch the shore marks, and check again when the wind changes.
- Mooring or anchoring too long. Arizona law says anchoring or fastening to shore for more than 14 consecutive days on public waters is illegal unless you move 25 nautical miles or more, or it is a special anchorage, private mooring or authorized by the governing agency (Arizona Game and Fish boater handbook).
The right unit for the way you anchor
Pontoons and deck boats are popular for anchoring and swimming. Check there is a bow anchor point you can reach, a locker that holds the rode and a boat that is stable with people on board. See our used boats, or look at Barletta and Bentley pontoons. We are an authorized dealer for Barletta and Bentley pontoons.
Related guides: How to anchor in Lake Havasu · How to tie a cleat hitch · How to tie a figure eight
Common questions
How much anchor line should I let out?
A common guideline is five to seven times the water depth, more in wind. Your anchor maker may give a different figure for your boat.
Why does my anchor drag?
Most often too little scope, the wrong anchor for the bottom, or the anchor was dropped while the boat was moving instead of being set.
What anchor is best for sand?
A fluke or Danforth style anchor is a common choice for sand and mud. Check the size against the maker's chart for your boat.
How do I know the anchor is holding?
Line up two fixed objects on shore and watch them. If they shift, the boat is moving.
Where do I tie the anchor line?
To a bow cleat or fitting, never the stern.
Next step
See what is on the lot in our used boat inventory, or call (928) 453-8833, text (928) 732-2281 or stop by 1680 Industrial Blvd in Lake Havasu City (Monday to Saturday 8 to 5, Sunday 9 to 2). Have a boat, pontoon, jet ski or trailer to sell? We consign it with no fees: we agree on a fair market value with you, and you get a check within 10 business days after the deal is funded.
