Wheel bearings let each trailer wheel spin on its axle. They live in grease, and when the grease breaks down or water gets in, they run hot and fail, often on the highway. Repacking means taking the hub apart, cleaning the bearings, inspecting them, replacing what is worn, and refilling with fresh grease. If you have not done it before, a shop can do it, or a mechanically comfortable owner can learn it from the trailer’s manual and the axle maker’s guide.
What the bearings do
Each hub has an inner and an outer bearing, a seal and a retaining nut with a locking device. The seal keeps grease in and water out. Some trailers use bearing protectors or oil-bath hubs, which need their own service, so check what you have before you start. The grease type, the nut setting and the service interval depend on your axle, so find them in your trailer’s manual, on the axle or hub tag, or from the axle maker. We do not print specifications here for that reason.
Tools and supplies
- Floor jack, jack stands rated for the trailer, and wheel chocks
- Lug wrench, hammer and punch or a seal puller, pliers, a bearing packer or gloves for hand packing
- Solvent for cleaning, shop rags, a drip pan
- New seals, cotter pins and the grease your axle maker specifies
- Replacement bearings and races if yours are worn, bought as a matched set for your hub
Steps in order
- Chock the wheels that stay on the ground, lift the trailer, and support it on stands. Never work under a trailer held only by a jack.
- Remove the wheel. Pry off the dust cap, pull the cotter pin, and take off the nut and washer.
- Pull the hub off the spindle, catching the outer bearing. Remove the seal and the inner bearing.
- Clean the bearings, races and hub completely with solvent and let them dry. Do not spin a bearing with compressed air.
- Inspect each bearing. Pitting, scoring, heat discoloration (blue or dark), broken cages or rough rotation mean replace the bearing and its race together.
- Pack each bearing with grease, working it through the rollers until grease comes out the other side. Add some to the hub cavity as the manual calls for.
- Fit the inner bearing and a new seal, seated square. Slide the hub on, fit the outer bearing, washer and nut.
- Adjust the nut as the axle maker specifies, fit a new cotter pin, and replace the dust cap. Spin the wheel to check for smooth rotation.
- Repeat on each wheel, then torque the lug nuts to the trailer’s specification after lowering the trailer, and recheck after a short drive.
Havasu conditions
Havasu heat is the backdrop for all of this. Go Lake Havasu’s climate table (credited to usclimatedata.com) shows an average July high of 109 degrees and an average August water temperature of 87 degrees (Go Lake Havasu), and the National Weather Service notes that the warmest temperature ever recorded at one of its official observing sites, 128 degrees on June 29, 1994, came from Lake Havasu City. Hot pavement and long drives heat hubs. Boat trailers also get dunked at the ramp, and a hot hub meeting cold lake water can pull water past a seal. Let the hubs cool before backing in, and check the hubs by hand (carefully) after a drive. A hub that is too hot to touch for a moment is a warning. Check hubs, tires and lights before heading out. See our guide on towing a boat or RV to Lake Havasu.
Signs of trouble
- A hub much hotter than the others, grease on the wheel or brake parts, or a burning smell
- Wheel wobble, rumbling or squealing at speed
- Rust-colored grease or water in the hub
When it needs a shop
- Trailers with brakes, since brake parts sit in the same area and need proper handling
- Damaged spindles or races that will not come out
- Any wheel that has been running hot or has seized
- If you do not have jack stands or a safe place to work
Trailers and what you buy
A trailer is included with every boat we sell. We do a full inspection before the paperwork is final and show you the reconditioning and maintenance we performed. See our boats, and standalone trailers.
Related guides
Towing a boat or RV to Lake Havasu, Storing a boat or RV in Lake Havasu for the summer, How to back a boat trailer into the water, How to load and unload a boat at the ramp.
Next step
Call us at (928) 453-8833, text (928) 732-2281, or stop by 1680 Industrial Blvd. Hours are Monday to Saturday 8 to 5 and Sunday 9 to 2. You can see our current boats, and if you have one to sell, we consign it with no fees. If you want to know what yours is worth first, start with a value estimate.
Common questions
How often should I repack trailer wheel bearings?
Follow your axle or trailer manual. Many owners repack yearly or after heavy use, and sooner after submerging the hubs.
What grease do I use?
Use the grease your axle maker specifies. Do not mix types unless the maker says it is safe.
How do I know a bearing is going bad?
Heat, noise, wobble, or grease leaking from the hub. Pull and inspect the hub if you see any of those.
Should I dunk hot hubs at the ramp?
Let them cool first. A hot hub meeting cold water can draw water past the seal.
Do bearing protectors replace repacking?
They help keep grease in and water out, but they still need checks and service. Follow the maker’s instructions.
