When a depth finder misbehaves, start with the simple things: power, the connection at the back of the unit, the transducer and what it is looking through. Most problems are a loose plug, a dirty or misplaced transducer, a weak battery or a setting that was changed. Work through the causes in order before you buy a new unit.
How a depth finder works
A transducer sends a sound pulse down and listens for the echo. The unit measures the time and shows depth. The transducer must sit in the water, clean, pointed down, and clear of turbulence from the hull, because bubbles block the signal. It can be mounted on the transom, inside the hull (shoot-through), or on the engine’s trolling motor. The mounting type is in your unit’s manual. Always follow that manual for settings and the transducer’s installation.
Tools and supplies
- The unit’s manual (or a copy from the maker’s website)
- A multimeter, spare fuses and a soft cloth
- Electrical contact cleaner and dielectric grease for the plugs
- Marine wire connectors, a screwdriver and a flashlight
Troubleshooting in order
- No power. Check the battery switch, the fuse or breaker, and the connections at the unit. Measure voltage at the plug. A weak battery can reset the unit or make it flicker.
- Screen on but no depth, or dashes. Check that the transducer plug is fully seated and clean. Look for a cut, pinched or chafed cable.
- Check the transducer. Is it in the water? Is it covered in scum, algae or a film? Wipe it clean. On a transom mount, check that it sits level, pointing straight down, below the hull’s bottom edge and clear of the prop wash.
- Works at rest but loses bottom at speed. Turbulence or bubbles under the transducer. Try raising or lowering it a little, or moving it. A damaged hull edge or strake near the transducer can cause this. A shoot-through install may need better bedding.
- Flickering depth or false readings. Look for noise from other equipment: the engine, a trolling motor, a bilge pump or a VHF radio. Run the boat and switch items on and off to find the source. Check that the power and transducer cables are separated from other wires.
- Shows very shallow depth or wrong depth. Check the settings: sensitivity, range, the keel offset and the units. Reset to defaults if the manual says how.
- Cloudy or dim screen. Check brightness and look for moisture behind the screen. Sun glare is a different problem, so a visor helps.
- If a test with the transducer in a bucket of water on the dock still shows nothing, suspect the transducer or the unit.
Havasu conditions
Havasu heat is the backdrop for all of this. Go Lake Havasu’s climate table (credited to usclimatedata.com) shows an average July high of 109 degrees and an average August water temperature of 87 degrees (Go Lake Havasu), and the National Weather Service notes that the warmest temperature ever recorded at one of its official observing sites, 128 degrees on June 29, 1994, came from Lake Havasu City. Screens left in the sun get hot and can dim or fail, and the heat in a closed console is hard on electronics. Take the unit off or cover it when you park, and keep the plugs clean and dry. Lake level changes, so readings that look unusual may be right: shallow water near sandbars and coves is real, and a depth finder does not replace a careful eye. Always slow down in unfamiliar shallows, and look at the Havasu boating laws and no-wake areas before you go.
When it needs a shop
- The unit powers on but never reads depth after you have cleaned and reseated everything and tested in water
- A cracked transducer or a transducer that is glued inside the hull and needs to be moved
- Screens with moisture inside, or burnt connectors
- Any interference you cannot trace
Electronics and the boat you buy
Check the electronics on any used boat and ask which are included. See our boats. We do a full inspection before the paperwork is final and show you the reconditioning and maintenance we performed.
Related guides
Battery maintenance, Pre-season checklist, Required safety equipment checklist, Lake Havasu by boat: Bridgewater Channel, coves and sandbars.
Next step
Call us at (928) 453-8833, text (928) 732-2281, or stop by 1680 Industrial Blvd. Hours are Monday to Saturday 8 to 5 and Sunday 9 to 2. You can see our current boats, and if you have one to sell, we consign it with no fees. If you want to know what yours is worth first, start with a value estimate.
Common questions
Why does my depth finder lose the bottom at speed?
Bubbles and turbulence under the transducer. Check its position, the hull near it, and the bedding if it is a shoot-through install.
Why does the depth read zero or dashes?
The transducer may be out of the water, dirty, unplugged or damaged. Clean it, reseat the plug and check the cable.
Can other electronics cause interference?
Yes. Engines, trolling motors, pumps and radios can add noise. Switch items off one at a time to find the source.
How do I know if the transducer has failed?
If the unit has power and settings are right, and a test in water shows nothing, the transducer or unit is suspect. A shop can test it.
Is a depth finder enough in shallow water?
It helps, but it is not a replacement for a lookout and slow speed in unfamiliar shallows.
