Small chips and scratches in gel coat can be filled and sanded at home with a repair kit. Larger cracks, damage that goes into the fiberglass, and color matching on a faded boat are often better handled by a shop. The goal is to seal the damage so water does not get into the laminate, and to make the repair blend in.
What gel coat is, and why it matters
Gel coat is the outer, colored resin layer over the fiberglass structure. It shields the laminate from water and UV. A chip that exposes the fiberglass can let water in, and over time the damage can spread. Scratches that stay in the gel coat are cosmetic, while chips and cracks that reach the fiberglass need to be sealed.
Tools and supplies
- A gel coat repair kit in a color that matches your boat (colors fade, so match against a clean, polished spot)
- Catalyst (hardener) that comes with the kit, and mixing sticks and cups
- Wet-and-dry sandpaper in a range of grits, and a sanding block
- Rubbing compound and polish, wax
- Masking tape, acetone for cleanup, gloves, safety glasses, a respirator for sanding
Steps for a chip or gouge
- Clean the area with a degreaser or acetone and dry it. Remove loose bits and feather the edges with a small tool or sandpaper.
- Tape around the repair to protect the good surface.
- Mix a small amount of gel coat with catalyst exactly as the kit directs. Too much or too little hardener causes a soft or sticky cure.
- Press the mix into the chip with a putty knife or the stick. Slightly overfill, because it shrinks as it cures. In a deep gouge, build up in layers.
- Many kits call for covering the repair with plastic wrap or a wax additive so it cures without air contact. Follow the directions.
- Let it cure fully, as long as the kit says. Cure time depends on temperature and mix.
- Sand flush with progressively finer wet-and-dry paper, keeping the surface wet and sanding only the repair.
- Compound and polish to bring up the gloss, then wax the area.
Scratches that have not gone through
If a scratch does not catch a fingernail, it may buff out. Try a polish or fine rubbing compound by hand before reaching for filler. Compound removes a little gel coat each time, so do not overdo it.
Color matching and sun
Havasu heat is the backdrop for all of this. Go Lake Havasu’s climate table (credited to usclimatedata.com) shows an average July high of 109 degrees and an average August water temperature of 87 degrees (Go Lake Havasu), and the National Weather Service notes that the warmest temperature ever recorded at one of its official observing sites, 128 degrees on June 29, 1994, came from Lake Havasu City. Sun fades and chalks gel coat, so the color on your boat is usually lighter than the color in a fresh kit. Polish a spot clean, then compare. Pigment tinting for an exact match is tricky, especially with blues, reds and darks, and a patch can stand out. For visible areas, a shop that blends the color is worth the cost. Do repairs in shade, in the cooler part of the day, because the catalyst reacts faster in heat and gives you less working time.
When it needs a shop
- Cracks that run in lines, or a web of cracks around a fitting or a stress point
- Soft, flexing or delaminated fiberglass, which is a structural problem
- Blisters across the hull
- Damage near the transom, through-hull fittings or the keel area
- Any repair on a boat you plan to sell, where color match counts
When you shop or sell
Buyers notice gel coat. A clean repair is fine, and a bad patch raises questions. If you plan to sell, we can talk it over. We consign boats with no fees, and we agree on a fair market value with you. See value estimate, or browse our boats.
Related guides
Hull cleaning and waxing, Storing a boat or RV in Lake Havasu for the summer, Towing a boat or RV to Lake Havasu.
Next step
Call us at (928) 453-8833, text (928) 732-2281, or stop by 1680 Industrial Blvd. Hours are Monday to Saturday 8 to 5 and Sunday 9 to 2. You can see our current boats, and if you have one to sell, we consign it with no fees. If you want to know what yours is worth first, start with a value estimate.
Common questions
Can I repair gel coat myself?
Small chips and scratches, yes, with a kit. Cracks, soft spots and blisters need a shop, since they can mean damage below the surface.
Why does my repair not match?
Gel coat fades in sun, so the kit color often differs from your boat. Test on a polished spot, or let a shop blend the color.
How long does gel coat take to cure?
It depends on the product, mix and temperature. Follow the kit directions and do not sand before it is fully hard.
What is the difference between gel coat and paint?
Gel coat is the molded resin surface of fiberglass boats. Paint is a separate coating applied on top. Repair methods differ.
Will a repair hurt resale?
A neat, color-matched repair rarely does. Poor patches stand out, so use a shop for visible damage.
