If you trailer your boat from Lake Havasu to the coast, flush the engine with fresh water as soon as you are out of the salt, before it dries. Salt dries into crystals that corrode metal and clog cooling passages. Use flush muffs or a built-in flush port as your manual directs, run the engine only if the manual approves running it with that water supply (and only with water flowing), and rinse the rest of the boat and trailer too.
Why Havasu owners need this
Lake Havasu is fresh water, so a flush is not a routine job at the lake. But when you tow to the coast, salt gets into the cooling system and onto every metal part. Rinse the engine soon after you leave the water, and again when you get home. Salt left to dry does the damage.
What you need
- A garden hose with fresh water and a spray nozzle.
- Flush muffs (ear muffs) sized for your lower unit, or a flush port if your engine has one.
- Your owner's manual for your engine's flush method and any limits, since methods differ for outboards, sterndrives and inboards.
Flushing an outboard, step by step
- Park on the ramp or at home with the engine upright and, if on a trailer, in a position the manual allows.
- Choose the method your manual specifies. With flush muffs, fit them over the water intakes on the lower unit; the muffs must seal and cover the intakes. With a built-in flush port or flushing attachment, connect the hose to it. Some makers prohibit running the engine at all when you use their built-in flushing attachment; Yamaha is one (Yamaha flushing instructions).
- If your manual approves running the engine with flush muffs, turn on the water first, then start the engine. Never run it with no water flowing, because the water pump impeller can be damaged in seconds. If you are using a built-in flushing attachment that the manual says not to run the engine with, leave the engine off.
- When running the engine is approved, run it at idle in neutral for the time the manual specifies. Watch for a strong stream from the tell-tale outlet.
- Shut off the engine if it is running, then the water, and remove the muffs or hose.
- Rinse the powerhead area and lower unit with fresh water, wipe the engine down and spray a corrosion inhibitor if your manual recommends one.
Sterndrives and inboards flush differently, often through a hose connection on the raw water system. Follow your manual. Also see impeller service.
Rinse the rest of the boat and trailer
- Wash the hull, deck, hardware, rails and canvas with fresh water.
- Rinse the trailer, especially the frame, springs, brake parts, lights, hubs and wheels. Salt corrodes brakes and wiring quickly. Check the wheel bearings later, see wheel bearing repacking.
- Flush or rinse live wells, bilge pumps and the washdown system if you used them in salt water.
- Check the sacrificial anodes (zincs). See zincs and corrosion protection.
Mistakes
- Waiting days to flush. Salt dries and hardens.
- Starting the engine before the water is on.
- Muffs that do not seal, so the pump sucks air.
- Flushing in neutral at a high throttle. Idle is enough unless your manual says otherwise.
- Forgetting the trailer, which often rusts first.
- Skipping corrosion protection and an inspection of electrical connections.
Havasu rules still apply
When you come home, clean, drain and dry the boat before launching in Lake Havasu, and check the aquatic invasive species guidance of the BLM (BLM Lake Havasu Field Office). Confirm any current requirements with Arizona Game and Fish. Arizona State Parks advises to pull the plug, clean, drain and dry (Arizona State Parks).
A boat built for coast and lake
If you plan to use your boat in salt water, ask about corrosion protection, stainless hardware and anodes. See used boats. We are an authorized Mercury and Volvo Penta dealer.
Related guides: Zincs and corrosion protection · How to change a boat impeller · Trailer wheel bearing repacking
Common questions
Do I need to flush after using the boat in Lake Havasu?
Lake Havasu is fresh water. Flushing is for salt water use, though your manual may call for flushes at other times, such as storage.
How soon should I flush after salt water?
As soon as possible after you leave the salt, and again when you get home. Salt dries and corrodes.
Can I run the engine without water?
No. If your manual approves running the engine during a flush, turn the water on before starting it, because running dry can destroy the water pump impeller. Some flushing attachments must be used with the engine off, so follow your manual.
How long do I flush it?
Check your owner's manual for the time and method for your engine.
Do I need to rinse the trailer?
Yes. Salt corrodes brakes, wiring and the frame, so rinse the trailer too.
Next step
See what is on the lot in our used boat inventory, or call (928) 453-8833, text (928) 732-2281 or stop by 1680 Industrial Blvd in Lake Havasu City (Monday to Saturday 8 to 5, Sunday 9 to 2). Have a boat, pontoon, jet ski or trailer to sell? We consign it with no fees: we agree on a fair market value with you, and you get a check within 10 business days after the deal is funded.
