The impeller is a rubber paddle wheel in the water pump that pushes cooling water through your engine. When it wears, the engine overheats. To replace it, identify your engine, buy the matching kit, open the pump housing, swap the impeller, reassemble with the right gaskets and check the water stream.
Why it matters in Havasu
The average July high is 109 degrees and the August water temperature averages 87 (Go Lake Havasu climate table). A weak cooling system gets found out in that heat. Follow the interval in your owner's manual or have the impeller checked each season.
Step one: identify the engine and the part
- Write down the make, model, horsepower, model year and serial number from the engine's ID plate.
- Look up the water pump kit for that exact engine in the maker's parts book or ask a dealer. Parts vary by year and by engine family, so do not buy on horsepower alone.
- A kit usually includes the impeller, a housing, gaskets and seals. We are an authorized Mercury and Volvo Penta dealer, so for those engines, ask for the right kit by model and serial number. Check your owner's manual or the engine maker's manual for the exact part.
Signs the impeller is worn
- The overheat alarm sounds, or the temperature gauge climbs.
- A weak or no stream from the tell-tale outlet.
- Steam or hot smell from the engine.
- The impeller has not been replaced within the maker's interval, or it has been run dry.
Stop the engine at the first sign of overheating. Running hot can ruin an engine.
Replacing it, in order
Details differ by engine. This is the general order, and your service manual rules.
- Disconnect the battery, or on an outboard remove the kill switch lanyard and disconnect the spark plug leads, so the engine cannot start.
- Open access to the pump. On an outboard, that usually means removing the lower unit from the midsection. On a sterndrive or inboard, it is often a raw water pump with a cover plate you can reach.
- Before taking it apart, note how everything fits. Take photos.
- Remove the pump housing and pull the old impeller. Look for missing vanes. Pieces left in the system can block cooling passages, so find them.
- Check the housing and plate for wear and scoring, and replace them if worn.
- Fit the new impeller in the same rotation direction as the old one, lubricating it with the grease the maker specifies. Vanes should lean the way the manual shows.
- Fit new gaskets and seals and reassemble. Torque fasteners to the manual's values, not by guesswork.
- Reconnect the battery or leads. If your manual expressly approves running the engine on a water supply such as flush muffs, connect it and run the engine on water to check the tell-tale stream and for leaks. Some built-in flushing attachments require the engine off (Yamaha flushing instructions), so otherwise test in the water.
Mistakes
- Buying the wrong kit by horsepower alone.
- Fitting the impeller backward.
- Reusing old gaskets and housings.
- Starting the engine dry. Even a short dry start can ruin the new part.
- Missing a broken vane in the hose or cooling passage.
- Not checking the tell-tale after the job.
- Replacing the impeller but ignoring the thermostat, hoses or clogged passages when the engine still runs hot.
Do it yourself or hire it out
This is within reach of a careful owner with the service manual. If the lower unit has to come off and you have not done it, a marine technician can do it. After saltwater use, flush first (see flushing a boat engine).
Buying a boat with known service history
Ask what has been serviced and when. We do a full inspection before the paperwork is final and show you the reconditioning and maintenance we performed. See used boats, and ask which engine each one has.
Related guides: How to flush a boat engine · Engine oil change · Pre-season checklist
Common questions
How often should I change a boat impeller?
Follow the interval in your engine maker's manual. Many owners also inspect it every season.
How do I know which impeller kit to buy?
Use the engine make, model, year and serial number from the ID plate, and check the maker's parts book or ask a dealer.
What happens if the impeller fails?
Cooling water stops flowing, the engine overheats and it can be badly damaged. Stop the engine at the first overheating sign.
Can I run the engine to test the new impeller?
Only with water supplied by a method your manual expressly approves for running that engine, or in the water. Some built-in flushing attachments require the engine off. Never run it dry.
Do I need to remove the lower unit?
On most outboards, yes. On many sterndrives and inboards the pump is reachable without that. Check your service manual.
Next step
See what is on the lot in our used boat inventory, or call (928) 453-8833, text (928) 732-2281 or stop by 1680 Industrial Blvd in Lake Havasu City (Monday to Saturday 8 to 5, Sunday 9 to 2). Have a boat, pontoon, jet ski or trailer to sell? We consign it with no fees: we agree on a fair market value with you, and you get a check within 10 business days after the deal is funded.
