An oil change on a four-stroke outboard or a sterndrive or inboard gasoline engine is a job most owners can do in a driveway: warm the engine, drain the old oil, replace the filter, refill to the mark, and check for leaks. The details that matter, oil grade, capacity and filter, depend on your engine, so read them from your owner’s manual or the engine’s data plate, not from a forum post. Two-stroke outboards that burn oil mixed with fuel have no crankcase oil to change, so this guide does not apply to them.
What the oil does on a boat
Engine oil lubricates, cools and carries away combustion by-products. A marine engine spends long hours at steady, high load, then sits. That combination is hard on oil, which is why many manufacturers tie the change to engine hours and to the calendar, whichever comes first. Your manual gives the schedule. A boat that sits most of the year still needs fresh oil, because used oil holds moisture and acids that attack bearings while the engine sits.
Tools and supplies
- The oil grade and quantity your manual specifies, plus a little extra
- The correct oil filter for your engine (match it by engine model, not by guesswork)
- A drain pan sized for the full capacity, or an oil extraction pump if your engine is set up for it
- Filter wrench, sockets for the drain plug, a funnel, shop towels, nitrile gloves
- Oil absorbent pads for the bilge or driveway, and a labeled container for used oil
- Your logbook, to record the date and engine hours
Steps in order
- Run the engine until it is warm so the oil flows, then shut it off. On the trailer, use a water-supply method your manual expressly approves for running that engine, or be in the water. Some built-in flushing attachments require the engine off (Yamaha flushing instructions). Never run a raw-water-cooled engine dry. Check your manual for how to run it.
- Tilt or position the engine as the manual directs so the oil drains fully. Outboards usually have a drain plug at the base of the powerhead area and a separate method for the lower unit gear oil, which is a different job.
- Set the pan under the drain, remove the plug and let it drain until the flow is a slow drip. Inspect the plug washer and replace it if it is crushed.
- Remove the old filter. Wipe the mounting surface clean. Coat the new filter’s rubber gasket with a thin film of fresh oil and thread it on by hand to the tightness the filter or manual calls for. Do not over-tighten with a wrench.
- Refit the drain plug with a clean washer, snug to the manual’s specification.
- Pour in the specified oil, a little under the full amount, and wait. Check the dipstick on level ground and top up to the mark. Never overfill.
- Start the engine (with water supplied), watch for oil pressure and look under the engine for leaks. Shut it off, wait, and recheck the dipstick.
- Dispose of the used oil and filter properly. Most auto parts stores and county collection sites accept them. Check with the one you use.
What Havasu heat does to oil
Havasu heat is the backdrop for all of this. Go Lake Havasu’s climate table (credited to usclimatedata.com) shows an average July high of 109 degrees and an average August water temperature of 87 degrees (Go Lake Havasu), and the National Weather Service notes that the warmest temperature ever recorded at one of its official observing sites, 128 degrees on June 29, 1994, came from Lake Havasu City. Engines run hot under those conditions, and a boat parked in the sun cooks the oil in the crankcase between trips. Check the level more often in summer, and look at the oil on the dipstick. Milky or creamy oil means water is getting in. Very dark, thick or gritty oil, or a fuel smell, means stop and have it looked at.
When it needs a shop
- Milky oil, metal glitter in the drained oil, or a sudden rise or drop in oil level
- Low or fluctuating oil pressure after a change
- A leak that continues after the plug and filter are seated
- Inboard or sterndrive engines where the drain is hard to reach, or any engine still under warranty where the maker wants dealer-documented service
We are an authorized Mercury and Volvo Penta dealer, so if you are unsure about the schedule or the parts for your engine, call us.
Owning the right engine and boat
Shopping for a used boat, ask when the oil was last changed and look at the dipstick yourself. We do a full inspection before the paperwork is final and show you the reconditioning and maintenance we performed. See our current boats.
Related guides
How to change a boat impeller, How to winterize a boat engine, Storing a boat or RV in Lake Havasu for the summer, How to flush a boat engine after salt water use.
Next step
Call us at (928) 453-8833, text (928) 732-2281, or stop by 1680 Industrial Blvd. Hours are Monday to Saturday 8 to 5 and Sunday 9 to 2. You can see our current boats, and if you have one to sell, we consign it with no fees. If you want to know what yours is worth first, start with a value estimate.
Common questions
How often should I change my boat engine oil?
Follow your owner’s manual, which usually ties the change to engine hours or a calendar period, whichever comes first. A boat that sits still needs fresh oil before storage.
Can I use car oil in my boat?
Only if your engine maker says so. Marine engines often call for a specific oil rating, so use what your manual specifies.
Where do I find my oil capacity and filter number?
In the owner’s manual or on the engine data plate. If you do not have either, call a dealer with your engine model and serial number.
Do two-stroke outboards need an oil change?
Not in the crankcase, since the oil is burned with the fuel. They still have lower unit gear oil that needs its own service.
What should I do with the used oil?
Take it in a sealed, labeled container to an auto parts store or county collection site. Do not pour it in the bilge, the lake or a drain.
