Hitching a fifth wheel comes down to a straight, slow back-up, a locked jaw you have confirmed by sight and by a tug test, and a walk-around before you move. Do it in the same order every time and it takes little time and rarely goes wrong. The steps below assume the hitch is already installed in the truck bed.
Before you hitch
- Confirm your truck can carry the load. The trailer’s pin weight and the truck’s payload and hitch ratings are on the trailer data plate, the truck’s door-jamb placard and the hitch label. Check your owner’s manuals for the numbers; they differ by unit, and so does the hitch rating.
- Park the trailer on firm, level ground with the wheels chocked. Soft ground lets the landing gear sink partway through the job.
- Set the landing gear so the underside of the kingpin plate sits a little lower than the top of the hitch plate. The pin should slide up the throat of the hitch and under the jaws, not climb on top of the plate.
- Look at the hitch. Plate clean and greased (or fitted with a lube disc, if the hitch maker allows it), jaw open, release handle in the open position.
Step by step
- Line the truck up square to the trailer, tailgate down or removed, and back slowly with a spotter or a camera. Use short, small steering corrections.
- Stop with the hitch a foot or so from the pin and check alignment. Fixing a crooked approach now is easier than after contact.
- Back the last distance at walking pace until the pin seats and the jaw closes. You will hear and feel it lock.
- Look at the hitch. The jaw should be closed around the pin shank, and the safety latch or locking pin should be in place. Do not rely on sound alone.
- Plug in the electrical cord, attach the breakaway cable to the truck as the manual directs (not to the hitch release), and test turn signals, brake lights and marker lights with a helper.
- Set the brake controller, apply it by hand, and confirm the trailer brakes engage. Arizona requires trailer brakes at a gross weight of 3,000 pounds or more, and a breakaway system that applies them if the trailer separates (A.R.S. 28-952). Confirm the current rule with the state.
- Do the tug test the way the hitch manufacturer describes it (CURT hookup procedure): with the trailer brakes applied by hand at the brake controller and the landing gear positioned as the manufacturer specifies, shift to a low gear and pull gently forward against the locked trailer. If the pin is not captured, you want to find out now.
- Raise the landing gear fully. Check that the handle or motor is stowed.
- Close the tailgate before you travel, if you lowered it.
- Pull the chocks, and do a last walk-around: tire condition, hitch, cable, lights, slide-outs in, steps up, door and compartments latched.
Mistakes that cause damage
- Backing in crooked and forcing it. Pull forward and start over.
- Skipping the tug test.
- Driving off with the landing gear down. It is the most common cause of a bent leg and a torn-up campsite.
- Hitch height wrong. Too low and the trailer lands on the plate; too high and the pin misses the throat. Adjust the landing gear, not the truck.
- Short-bed trucks: the trailer front can hit the cab in a tight turn. Ask whether your hitch needs a sliding mount, and check your manual before backing into a campsite.
Unhitching
Reverse the order. Chock the trailer wheels, lower the tailgate, lower the landing gear until it takes weight, unplug and stow the cord and breakaway cable, release the jaw, then pull out slowly. Do not unhitch on a slope without chocks.
The Havasu angle
Summer is hard on tires and brake wiring. The National Weather Service recorded the warmest temperature at an official observing site in Lake Havasu City, 128 degrees Fahrenheit on June 29, 1994. Check tire condition and cable condition before every summer trip. For route rules and heights and lengths, see Towing a Boat or RV to Lake Havasu.
Owning the right rig
A fifth wheel tows best behind a truck rated for the pin weight with room left in the payload. When you shop, bring the truck’s placard numbers with you and ask which fifth wheels fit within them. See the RVs we have listed.
Common questions
Where do I find my fifth wheel hitch rating?
On the label on the hitch itself and in the hitch manual. Compare it with the trailer pin weight on the data plate and your truck payload on the door-jamb placard.
How do I know the jaws are locked?
Look at the jaw closed around the pin and confirm the safety latch or locking pin is in. Then do the tug test the way the hitch manufacturer describes, with the trailer brakes applied. Do not rely on the sound.
Should I grease the hitch plate?
Most plates need lubrication or a lube disc, but check the hitch maker instructions. Some hitches are made to run dry.
Do I need trailer brakes in Arizona?
State law requires brakes at a trailer gross weight of 3,000 pounds or more. Check the current statute or ask ADOT.
Can I hitch alone?
Yes, with a rear camera and patience, but a spotter makes the alignment faster and safer.
Related guides
Next step
If you are shopping, browse the RVs we have listed, then call (928) 453-8833, text (928) 732-2281 or stop by 1680 Industrial Blvd in Lake Havasu City. We are open Monday to Saturday 8 to 5 and Sunday 9 to 2. Have an RV to sell? We consign it with no fees: we agree on a fair market value with you, and a check follows within 10 business days after the deal is funded.
