Start with how much electricity you use, not with panels. Add up your daily load, size the battery bank and the panels to cover it, then connect panels, charge controller, fuses and batteries in the right order. If you are not comfortable with wiring, have an RV technician do the connections.
Step 1: Add up your load
List every device you run off the battery: lights, fans, pump, refrigerator control board, phone chargers, laptop, and anything on an inverter. Multiply each device’s watts by hours per day. The sum, in watt-hours, is your daily need. An air conditioner is the big one. Most small systems do not run it.
Step 2: Size the pieces
- Battery bank. Enough capacity to cover your need for a night plus a reserve. Your battery type (lead acid or lithium) sets how deeply you can discharge, so check the maker’s data sheet.
- Panels. Sized to refill the battery in the sun hours you get. Use a conservative figure for daily sun, because panels rarely hit their label rating, especially when hot.
- Charge controller. Must match the panel voltage and current, and be set for your battery type. A controller with MPPT is common for larger arrays. The manual lists the limits.
- Inverter. Only if you need household outlets. Size it for the load and use proper cable.
- Wire and fuses. The wire gauge depends on current and length. Use the controller maker’s chart, and fuse or breaker every positive conductor close to the battery.
Step 3: Mount the panels
- Check the roof’s load rating and the layout of vents, air conditioners and skylights. Leave room to walk around them.
- Mount with brackets, bolt through or screw into solid structure as the roof maker allows, and seal every penetration with a sealant approved for your roof material. Check it again after the first summer. See our roof leak guide.
- Leave a gap under the panels for air flow, since heat reduces output.
Step 4: Wire it, in this order
- Cover the panels, or work in the dark, so they do not make current while you connect.
- Run panel cables through a proper roof gland to the controller location, near the batteries.
- Connect the controller to the battery first, with the fuse in place, so it can detect the voltage.
- Then connect the panels to the controller.
- Set the battery type, then uncover the panels and watch the display.
- Label everything, and record fuse sizes.
Safety
- Never work on a hot roof. Do roof work early in the morning, with the surface cool enough to touch, and have a second person on the ground. Stay clear of power lines and off a wet roof.
- Batteries can burn and spark. Remove rings, use insulated tools, and never short a battery.
- Lithium batteries need a compatible, correctly configured charge controller and the battery maker’s required battery management system (BMS) protection, whether built in or external (Victron system design guidance). Follow the maker’s instructions.
- Do not tap into shore-power wiring unless you know what you are doing.
The Havasu angle
Sun is the easy part here. Heat is the problem: Go Lake Havasu’s table lists an average July high of 109 degrees (Go Lake Havasu), and the National Weather Service reports a Lake Havasu City reading of 128 degrees on June 29, 1994. Hot panels and hot batteries lose performance, so give them airflow and shade the batteries. Dust on panels lowers output; wash them with plain water in the cool of the morning.
Owning the right rig
Some RVs are sold solar-ready, with wiring to the roof and a space for the controller. Ask when you shop. See the RVs we have listed. For more on what you really need, see Off-Grid Solar for RVs.
Common questions
How many solar panels do I need?
It depends on your daily watt-hour use and the sun you get. Add up your loads first, then size the panels and batteries.
Can solar run my air conditioner?
Most small systems cannot. It needs a large battery bank, a big inverter and enough panels, so plan for it from the start.
Which do I connect first, panels or battery?
The battery first, with a fuse, then the panels to the controller.
Does heat hurt panels?
Yes. Output drops as panels get hot, so leave airflow under them.
Can I do the wiring myself?
If you are experienced with DC wiring, yes. If not, have an RV technician do it, because mistakes can cause fires.
Related guides
- Off-Grid Solar for RVs
- How to Boondock Off-Grid in the Arizona Desert
- How to Maintain Your RV Generator
Next step
If you are shopping, browse the RVs we have listed, then call (928) 453-8833, text (928) 732-2281 or stop by 1680 Industrial Blvd in Lake Havasu City. We are open Monday to Saturday 8 to 5 and Sunday 9 to 2. Have an RV to sell? We consign it with no fees: we agree on a fair market value with you, and a check follows within 10 business days after the deal is funded.
