← Back to the Blog

How to Tie a Cleat Hitch on a Boat

A cleat hitch ties a dock line to a cleat so it holds under load and releases in seconds. Take one full turn around the base, cross the horns in figure eights, and finish with a locking turn. Done right it looks like a neat basket, not a ball of rope.

Before you tie

  • Check the cleat is solid. A cleat that flexes or is loose in the deck needs repair before it holds a boat.
  • Use a cleat sized for your line. Very small cleats do not hold large line.
  • Run the line from the boat fitting or the dock ring to the cleat at a fair angle, so the pull is along the cleat, not across it.

Steps, in order

  1. Take the line past the cleat and make one full turn around the base, under both horns. This turn takes the first load.
  2. Cross over the top of the cleat diagonally and go under the far horn.
  3. Cross back over the top diagonally and under the other horn. That is a figure eight. Two figure eights are normally enough.
  4. For the finish, make a loop in the line and slip it over the horn so the end of the line lies parallel to the line it came from. This locking turn stops the knot working loose.
  5. Pull the standing part snug. The turns should lie flat and not cross over each other.
  6. Coil the tail and leave it tidy, away from feet and pull points.

Many people also finish with a half hitch only. A proper locking hitch is better, and a pile of extra wraps on top does not help.

Common mistakes

  • Too many wraps. A bulky pile is hard to release when the line is loaded and holds no better.
  • Skipping the base turn. Without the first turn, the figure eights can slide.
  • Finishing with a locked hitch backward. If the finish loops over the wrong horn, it jams and cannot be released under load.
  • Tying in a hurry. A cleat hitch that looks like a ball is often only a tangle. Slow down and place each turn.
  • Tying a loaded line. If the boat is already pulling, hold the line on the cleat with a turn first, then build the hitch.

Releasing it

Ease the load on the line. Flip the locking hitch free and unwind the turns in reverse. Never stand in the bight of a loaded line.

Cleats on the boat you buy

Look at the number, size and mounting of cleats when you shop. Bow, stern and midship cleats let you rig proper dock lines. Browse used boats and see the hardware for yourself, or compare Barletta and Bentley pontoons. We are an authorized dealer for Barletta and Bentley pontoons.

Related guides: How to use dock lines · How to use fenders · How to tie a bowline

Common questions

How many wraps does a cleat hitch need?

One full turn around the base, then two figure eights, then a locking turn. More wraps only make it harder to untie.

Do I need the locking hitch at the end?

It is good practice, because it stops the hitch working loose when the line goes slack in a wake.

Which way should I tie it?

Either direction works if the pattern is the same. Keep the pull along the length of the cleat.

Can a cleat hitch hold a boat on its own?

Yes, if the cleat is solid and the knot is correct. Use two or more lines to the dock, not a single line.

How do I release a hitch that is under load?

Take the load off by pulling the boat toward the dock or using another line. Do not stand in the bight of a loaded line.

Next step

See what is on the lot in our used boat inventory, or call (928) 453-8833, text (928) 732-2281 or stop by 1680 Industrial Blvd in Lake Havasu City (Monday to Saturday 8 to 5, Sunday 9 to 2). Have a boat, pontoon, jet ski or trailer to sell? We consign it with no fees: we agree on a fair market value with you, and you get a check within 10 business days after the deal is funded.

Browse Boats Consign Yours