Sacrificial anodes, often called zincs, corrode on purpose so that the metal parts of your boat do not. Inspect them at the start of the season and replace them when they reach the replacement point your engine or drive maker specifies. Mercury’s published guidance is approximately half consumed (Mercury maintenance guidance). Water conditions affect which anode alloy suits your boat, so use the alloy and the locations your engine or drive maker specifies (Mercury anode specification).
How a sacrificial anode works
When two different metals sit in water that conducts electricity, the more active metal gives up material first. An anode is made of a more active metal than the aluminum, steel and bronze parts it protects, so the anode wears away while those parts survive. An anode that has been used up cannot protect anything, and the next metals in line start to corrode. Corrosion also comes from stray electrical current from poor wiring, shore power or a neighboring boat, which an anode cannot always handle, so a bonding and wiring check belongs in the job.
Water conditions affect anode choice
Anodes come in zinc, aluminum and magnesium, and each suits different water. In general, zinc is the common choice in salt water, aluminum is used in salt and brackish water, and magnesium is the usual choice in fresh water. The reason is how readily each metal gives up its charge in water with different conductivity. A zinc anode in fresh water can develop a surface film that stops it working, so it can look fine and protect nothing. Boats that move between waters, for example a Havasu boat trailered to the coast, may need a different setup. Your engine or drive maker’s manual says which anode material to use and where it goes. Follow that, and do not swap materials on your own. Some approved aluminum anodes work in both fresh and salt water, so the maker’s specification, not the water alone, decides. If you trailer to salt water, see our guide on flushing a boat engine after salt water use.
Where anodes live
- On outboards and sterndrives, on the gearcase, trim tab, bracket or transom assembly, depending on the model
- On the trim tabs, rudders, shafts and hull on larger boats
- Inside engine cooling passages on some engines, which need a shop to service
Your owner’s manual or the drive’s parts diagram shows the locations and part numbers. Part numbers vary by engine and drive, so we do not list them here.
Tools and supplies
- The correct replacement anodes for your engine or drive, in the material the maker recommends
- Sockets and a screwdriver for the mounting hardware
- A wire brush or sandpaper to clean the mounting surface, and a rag
- A multimeter, if you are checking for stray current
Inspection and replacement steps
- Inspect with the boat out of the water and the engine off. Look at each anode and note how much is left.
- Replace an anode when it reaches the replacement point your engine or drive maker specifies. Mercury’s published guidance is approximately half consumed.
- Remove the old anode and clean the mounting surface to bare metal. A painted or dirty contact stops the anode from working. Do not paint anodes.
- Fit the new anode with its hardware, snug and with good metal-to-metal contact.
- Check for corrosion on the metal around it: bubbling paint, white powder, pitting or flaking aluminum.
- Rinse the engine with fresh water after use, as your manual directs, and keep a log of when you replaced the anodes.
What Havasu heat and conditions do
Havasu heat is the backdrop for all of this. Go Lake Havasu’s climate table (credited to usclimatedata.com) shows an average July high of 109 degrees and an average August water temperature of 87 degrees (Go Lake Havasu), and the National Weather Service notes that the warmest temperature ever recorded at one of its official observing sites, 128 degrees on June 29, 1994, came from Lake Havasu City. Warm water speeds chemical reactions, including corrosion. Boats left at a slip or on a lift in warm water for months wear anodes faster than boats trailered out each weekend. Storage also matters: a boat that sits wet all summer needs more checks, and a boat that sits dry mostly needs the same protection when it goes back in. Check the anodes at the start of the season and again after a long stay in the water.
When it needs a shop
- Anodes that disappear much faster than expected, which can point to a stray current problem
- Corrosion on the gearcase, prop shaft or drive, or pitting in aluminum
- Internal engine anodes
- Choosing a different anode material for a boat that moves between fresh and salt water
We are an authorized Mercury and Volvo Penta dealer. If you are not sure which anodes belong on your engine, call us with the model and serial number.
Corrosion and the boat you buy
Look at the gearcase, trim tabs and the anodes on a used boat. Browse our boats. We do a full inspection before the paperwork is final and show you the reconditioning and maintenance we performed.
Related guides
How to flush a boat engine after salt water use, Pre-season checklist, Storing a boat or RV in Lake Havasu for the summer, How to change a boat impeller.
Next step
Call us at (928) 453-8833, text (928) 732-2281, or stop by 1680 Industrial Blvd. Hours are Monday to Saturday 8 to 5 and Sunday 9 to 2. You can see our current boats, and if you have one to sell, we consign it with no fees. If you want to know what yours is worth first, start with a value estimate.
Common questions
Do I need zincs in fresh water?
Anodes are used in fresh water too. Use the alloy your engine or drive maker specifies; some approved aluminum anodes work in both fresh and salt water.
Is zinc or magnesium better for Havasu?
Havasu is fresh water, and magnesium is the common choice for fresh water, but follow your engine or drive maker’s recommendation.
When should I replace an anode?
When it reaches the replacement point your engine or drive maker specifies, which for Mercury is approximately half consumed. Check at the start of each season and after long stays in the water.
Can I paint over an anode?
No. Paint blocks the contact and stops it working. Clean to bare metal where it mounts.
What if I trailer to the coast?
Salt water changes the needs. Ask your engine maker or a dealer, and flush the engine after salt water use.
