← Back to the Blog

Prop Inspection and Replacement: A Lake Havasu Owner’s Guide

Look at your propeller at the start of every season and after any hard contact with the bottom. Bent, chipped or nicked blades, a spun hub, fishing line behind the prop and a slipping feel under power are all signs to repair or replace it. Swapping a prop is a manageable driveway job, as long as the engine cannot possibly start while your hands are near the blades.

What the prop does

The prop turns engine power into thrust. Blade shape, diameter and pitch decide how the boat accelerates and what top speed it reaches, and the right prop is matched to your boat and engine. A damaged prop costs you speed and fuel, makes vibration that wears bearings and seals, and can overload the engine. For the right prop size and the recommended engine speed range, check your owner’s manual, then talk to a dealer before changing pitch or diameter.

Safety first

  • Take the key out and disconnect the battery or the kill switch lanyard clip before touching the prop.
  • On outboards, put the engine out of gear and tilt it, or work with the boat on the trailer.
  • Wear gloves. Blade edges are sharp even when they look dull.

Inspection steps

  1. Look at each blade edge for nicks, cracks, bends and curled tips. Small nicks can be dressed by a prop shop. Bends and cracks usually mean repair or replacement.
  2. Spin the prop by hand. It should turn smoothly with no wobble. Wobble means a bent blade or a bent shaft.
  3. Check behind the prop for fishing line wrapped around the shaft. Line can cut through the prop shaft seal and let water into the gearcase, which is a costly repair.
  4. Try to twist the prop on the shaft. A hub that spins independently of the shaft (a spun hub) shows up as engine speed rising without the boat speeding up.
  5. Look for oil or milky fluid leaking from the shaft seal area.
  6. Check the prop nut and cotter pin or locking tab. These must be intact.

Replacing the prop

  1. With the engine disabled, block the prop with a piece of wood against the anti-ventilation plate or the hull.
  2. Remove the cotter pin or bend back the locking tab, then remove the nut and washers. Note the order of the washers and spacers.
  3. Slide the prop off. If it is stuck, a prop puller is the safe tool. Do not pry on the lower unit.
  4. Clean the shaft, remove line and old grease, and inspect the splines for wear.
  5. Grease the shaft with the marine grease your manual specifies, fit the thrust washer and the new prop, then the washers and nut in the correct order.
  6. Tighten the nut to the torque in your owner’s manual, then fit a new cotter pin or lock tab. Never reuse an old cotter pin.
  7. Carry a spare prop and the tools to fit it. A spare in the boat beats a long tow.

Havasu conditions

Havasu heat is the backdrop for all of this. Go Lake Havasu’s climate table (credited to usclimatedata.com) shows an average July high of 109 degrees and an average August water temperature of 87 degrees (Go Lake Havasu), and the National Weather Service notes that the warmest temperature ever recorded at one of its official observing sites, 128 degrees on June 29, 1994, came from Lake Havasu City. Warm water and summer crowds mean a lot of time at speed, near the Channel, coves and sandbars. Debris, rocks near shore and the no-wake rules near ramps and shore are good reasons to trim up and slow down in shallow water. Lake level changes, so what was deep last season may not be this season. Check Reclamation or the Go Lake Havasu water page for current conditions before you go.

When it needs a shop

  • Bent shaft, wobble or vibration after you fit a good prop
  • Oil or water in the gearcase lube, or a leak at the prop shaft seal
  • Splines worn or damaged, or a stuck prop that will not come off with a puller
  • Picking a different pitch or diameter. A dealer can match it to your engine speed range.

The right setup when you buy

When you look at a used boat, check the prop and ask what is on the boat. A boat that is propped correctly reaches the engine’s recommended speed range at full throttle. Browse our boats, and for pontoons see Barletta and Bentley.

Related guides

How to change a boat impeller, How to flush a boat engine after salt water use, Required safety equipment checklist, How to trim a boat engine.

Next step

Call us at (928) 453-8833, text (928) 732-2281, or stop by 1680 Industrial Blvd. Hours are Monday to Saturday 8 to 5 and Sunday 9 to 2. You can see our current boats, and if you have one to sell, we consign it with no fees. If you want to know what yours is worth first, start with a value estimate.

Common questions

How often should I inspect my propeller?

At the start of each season and after any hit. Look more often if you boat in shallow coves or near debris.

Can a bent prop be repaired?

Often a prop shop can straighten a bent blade or dress small nicks. Cracks and heavy damage usually mean replacement.

What does a spun hub feel like?

The engine speed climbs but the boat does not speed up, or it slips under load. The hub has turned on its inner sleeve and the prop needs repair or replacement.

What size prop do I need?

Your owner’s manual gives the engine’s recommended full-throttle speed range, which sets the pitch and diameter. A dealer can help match the prop to your boat.

Should I carry a spare prop?

Yes. A spare, a prop wrench and a new cotter pin let you swap a damaged prop at the ramp instead of calling for a tow.

Browse Boats Consign Yours